Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have added the include and src. file paths to the MAKEFILE and yet I am experiencing this error.
I tried deleting the main.c.o file too, but am still experiencing this...
Hi,
After implementing my own services, I run into a problem when trying to read the value.of a characteristic. I basically have four services, of which one only holds one...
Dear Nordicsemi,
we need automatic simple test of ble function of our products - scanning bluetooth devices in rage and reading RSSI of device with specific mac address...
Sorry to bring up a topic which seems to have been discussed already, but I don't see an answer to my specific questions.
The original design of my project was to have both...
Hi,
The known issues section of SDK v1.3.0 release note states that
"
nRF5340
FOTA with the SMP Server Sample does not work.
"
Is this fixed in version 1.3.1?
Good morning, I'm working with the nRF52 DK and a custom board that has the nRF52810.
I am using the SDK 15.0.0 and followed the tutorial described here:
https://devzone...
Do you think my nrf is original?
The person I bought says it's original.
Can you please check it?
Seller link: http://www.ebyte.com/en/product-view-news.aspx?id=113
Hi,
I have a custom board in which i am using nRF52840 with SDK version is 16.0.0.
I have tested app_uart library its working Ok and current consumption is 6 uA in deep...
Hello,
I'm developing a project which uses two threads. One configures UART and keeps on a while(1) loop. But once it receives a byte, an ISR pushes the incoming byte...
Hello
I am adding the mpu6050 library in the ble_app_template of SDK 14.2.
Use the ble_mpu6050_simple example here. https://github.com/Martinsbl/nrf5-mpu-examples
I...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
