Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
Hi,
I was using nRF Mesh application to get the data of uint32_t from my server model(nRF52840) but nRF Mesh android application crashes while sending the opcode to the...
I am searching for complete developement kit and SDK support which can be used to form BLE mesh Network and BLE beacon device. The idea is that BLE mesh nodes will act as...
Good afternoon, dear Sir of Madam.
Our product used the NRF21540-QDAA-R7 which has gone obsolete. What is the best substitute part?
Unfortunatelly i couldn't find substitution...
Hi I am facing a issue regarding the DFU update using the nrfConnect App.
Since we recently updated from SDK12.0 to SDK16.0 and the softdevice version has been changed in...
Hi,
I am analyzing the power consumption of mesh nodes using your Power Profile Kit. I am running the example beaconing of the Mesh SDK 3.1.0 on a board nRF52832 with the...
I have designed a nrf9160 debugging board, which uses 18 and 19 pin as the log output. Then I also configure the TX and Rx of UART0 in the overlay file, which are 18 and 19...
i tried with blinky example like thiis
#pragma long_calls
__attribute__((used, long_calls, section(".data"))) int main(void) { /* Configure board. */ bsp_board_init...
Hi,
I'm working on a code using SPI.
I've changed the SPI configuration from this thread: https://devzone.nordicsemi.com/f/nordic-q-a/65072/nrf5430-spi-sample-code ...
Hi,
I'm working in a project where we try to implement an Isochronous broadcaster using timeslots, co-existing with Softdevice controlled Scanning and Connecting. We use...
Hello!
I use the latest versions of sdk v17 and nRF52DK, nRF52840.
I refer to examples written by others as well as basic examples of SDK. But I don't know if I can...
