Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I am using Thingy 52 to measure the acceleration from accelerometer. I was expecting values like m/s2 but I am seeing values in unit vector, ie, values between (0 -...
I have nrf52dk (nrf52832) board and a custom nrf52805 board. The nrf52805 board has no external 32kHz crystals, but only 32MHz crystal. Also, it is in LDO mode (no DC-DC inductors...
Device nrf52832, nrf5_SDK_for_Mesh_v3.2.0_src with nRF5_SDK_15.3.0_59ac345
Hello.
I want to transmit and receive some data between smartphone app and mesh sensor.(almost...
Hi, Im using nRF52840 DK, Segger Studio v4.52 and SDK version 17. I have been trying to make BLE OTA DFU work but have had many problems along the way. I followed the guides...
Hi folks,
I need a production test of an nRF52840 module at PCB level. Our board connects near instantly with nRF Connect + Bluetooth Low Energy, and displays its device...
Hi,
I am trying to implement wireless power transmission. For sending output voltage information from receiver board
to transmitter board continuously which of you module...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
I am working with the nRF52840 DK and was looking for a way to set a compare register to trigger at 300 ticks, and another to trigger at 40000 ticks. The register that triggers...
Hi,
I am a new comer so perhaps I made a mistake during project configuration.
I am using nrf Connect v3.4.2 on Windows.
I trie to add CC310 libray in sample hello_world...
The detected device could not be recognized as neither JLink nor BLE could be captured in wireshark, nor could the nRF Connect v3.4.2 - Programmer produce "Unsupported device...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both BLE scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi. This is my first experience using Nordic Products and I have run into some issues trying to "Open nRF Connect Studio Project" from SEGGER Embedded Studio. I want to run...
