Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I am test the DFU function in nRF52840. I want to add a timer to the bootloader to generate a one-second sleep action. But when even I have not started to use the timer...
After enabling both the Macro MESH_FEATURE_RELAY_ENABLED and MESH_FEATURE_GATT_PROXY_ENABLED as mentioned in this link ....
Does the proxy and relay feature work for light_switch...
Hello Support
I have a question about the function " uint16_t otCoapMessageGetMessageId(const otMessage *aMessage); ". I need to know the message ID for my application....
Hi,
I am facing a problem while setting up pyaci on Ubuntu 20.04.
On launching the command:
In [4]: p = Provisioner(device, db)
I am getting:
In [5]: 2020-08-04...
Hello guys,
In our current project, we need to have the ability to copy .bmp images from our PC directly to W25N01GVZEIG TR QSPI flash memory of NAND type. To the best...
Hello, i am new to the whole NRF programming. I created my custom board with a NRF52811 SoC, without external LF crystal. I have been trying to get the device to advertise...
Hi all,
I am working on eddystone scanner and I follow this post to start with. However, I have some problems:
1. The device isn't scanning without any modification of...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v13 and using keil mdk armv5.as a compiler. I build it successfully, but when I loaded the hex file...
I am trying to update the firmware on the Thingy:91 following the instructions here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi
I am using nordic thingy 91 and i want to program my application on nRF9160 and nRF52840 respectively and i am following the getting start guide.
first i was able to...
SDK 17.0.0/ Windows/nRF52840 DK/ SEGGER
Hi, I want to learn how to achieve the outcome of allowing the peripheral to advertise in the long-range and the Central DK to pick...
Hello,
I have an application in which I need to get RSSI before, during and after any BLE connection has been made. The RSSI measurements are being used to quantify the...
Hello, I am using nRF52 DK and SDK V15.2.0 with a Nordic PPK to measure current draw. I have read tons and tons of questions posted here but am still unable to figure out...
Hi all :) ,
I'm trying to create my new zip folder with new image.
I connect to my nrf52833, then i click on dfu button into nrfConnect mobil app.
I selec zip file...
I'm using:
OS : Windows 10
IDE : Segger Embedded Studio for ARM Realease 4.52c Windows x64
SDK : nRF_SDK_15.0.0_a53641a
In my project I'm using 4 pressure sensors...
