Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I am following the tutorial https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/getting-started-with-nordics-secure-dfu-bootloader...
Hello,
I really find this tutorial useful and substantial. I followed the steps in downloading the github projects but I got the following errors when compiling (Note: I...
Greetings everyone,
I am a beginner in this and would like to ask for help in reading battery level.
Battery info: 3.7V, 100mAh, 0.37wh.
I have tried to read on the...
hai ,
i my application i need to update ota over serial . i m using nrf52840 and sdk 15.2
step 1 : at first flashed uart boot loader code on my board
step 2 : updated...
Hello
I am testing connection between nrf51 dongle and my BLE keyboard using heart_rate_collector sample.but there is an issue with on_service_discovery_response.
my BLE...
Does exist any IC/module of Nordic which could be used as NFC reader/initiator and that has BLE integrated also?
Or just a little BLE module with on-board uFL connector...
Hi Devzone:
We are testing TX and RX range with our customized boards, and encountered a rather bizarre problem:
The connection range is pretty good indoor, maybe 20~30...
I am working on a driver for the Adesto AT25QL641 QSPI Flash Memory chip. Comparing the hardcoded nRF52840 QSPI instruction set and the AT25QL641, they are 90% identical except...
Hi,
I am trying to implement Zigbee mesh and in the Zigbee End device(ZED), I want to know its neighbor table record or routing table record. I did not found any specific...
Hi,
In my application,I have written a code based on ble_hrs sample example. When I am checking the RSSI value at the tablet at 2 meter distance I am getting -56dbm. As...
Hi,
I am planning to design my own custom PCB using the nRF52840 chip.
As I am getting started, I want to make sure all the design rule dimensions are up to the standard...
Hi All,
I am trying to design a BLE module based on the nRF52840 Configuration 6 (Only Battery) provided in the product specification document.
To get started I was using...
Hi,
I know that the S132 v6 didn't support multiple advertising sets with different advertising handles. If you want to advertise with new data or different parameters,...
Hi All,
If I am to use a Piezo Buzzer to generate sound using nRF52840 PWM:
1. any suggestion on how to design the circuitry?
I am planning to use a Murata cimponent...
Hi to all,
we are developing an application nrf52832 that use BLE and internal flash as storage.
The problem, as I wrote in the subject, is the write operation is never...
