We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I get an error fatal when running Heart rate collector example from SDK12 on PCA10040 development board.
The sensor use example from SDK15 on a nRF52840-DK.
Some...
Hi,
I want to use Segger Embedded Studio to write firmware for Thingy 52 but I don't know what programming hardware I need. Is there any documentation that supports Segger...
Hello,
Thank you for helping me to interface the Si7021 humidity and temperature sensor with Nordic nRF52 development kit board. I need to write the necessary code to finish...
Hi,
I am using nRF52832 for my development, I want to send 8 bit device ID as an advertising packet with company ID and Data.
Is thereany way to send the same or any example...
In earlier releases of the mfw for the nRF9160, we got 3 files with the image, one of them being firmware.update.image.hex. This is missing in the new updates. How do we update...
Hi, I have a PCA10000 nrf51 dongle, I use with wireshark and the nrf sniffer plugin. I followed all installation steps for the version 3 of the sniffer and the latest version...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send datas from sensor (accelerometer...
hi
i use sdk12.3 (51822), i see only ble_app_hids_keyboard and ble_app_hids_mouse.
I want use mouse +kb device. I use ble_app_hids_mouse add kb function . then my android...
Dear All,
For a reason that I can't understand so far, I must erase the nRF52840 to be able to use UART1, TX RX on pins 0 1 (connector P14) to communicate with an external...
Hi,
Do you know which of the two version of ADP5360 the Thingy 91 uses?
is it
ADP5360ACBZ-1-R7 or
ADP5360ACBZ-2-R7
Both versions are available now at Analog's...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
"nrfx_wdt_event_handler_t" can be set in "nrf_drv_wdt_init". After the "nrfx_wdt_event_handler_t" event occurs, the WDT is reset...
HI，
When I use NRF58240 to develop GPS positioning function, APP_UART_COMMUNICATION_ERROR appears, but when I do not connect the GPS module, there is no such error. What...
Is there any test firmware available (or reference code) for doing total radiated power measurements? I have the nRF9160 designed onto a PCB and we'd like to do some antenna...
