Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
I have a question regarding power - up sequence of NRF52840.
When the USB is plugged in, the VBUS voltage is at 5V.
However, at the same instant, VDDH is...
I have a nRF52840 Dongle that connects to a USB port on my computer. I have a device that can connect to it via BT and the readings are logged through the Nordic utility app...
At edit a file compile Run DEBUG , But Program Usually lead to unexpectedly run this loop for a period of time,How can I look for the origins of this bug
Hi ,
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fgetting_started_softdevice.html
In this link it says "
Before you program...
Hi,
I had to modify the peripheral blinky example by adding UART module .The program compiles and builds but it is not advertising.I guess there is some problem with the...
Dear All
We implement a DFU over USB functionality to the custom board nrf52840 board by compiling via gcc. Somehow there is my understanding problem with the linker for...
Hi
I wanted to add NUS_C service to multilink central example. I have nRF52-DK (PCA10040) evaluation boards at central and peripheral side. It compiles without errors but...
Hi,
I'm trying out the "Android nRF beacon for Eddystone" app (installed from PlayStore) with the Eddystone Beacon Application example on a PCA10040.
First off, I have...
Hi,
I want to change the bit rate in Mesh light switch example for long range (as of now getting only 15mtrs), i found that there is a function for update phys, but while...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (SDK ver. 12.3.0, SD ver. s130_2.0.1)
Situation is the following:
1. I use peer manager for deal...
I've written a detailed description of how to program & debug the NRF52832 using open-source tools and the Nordic SDK.
See https://iosoft.blog/arm-gcc-lean-nordic-nrf52...
Hi all
I am working on Bluetooth application using NRF52840 kit. The application is very simple, the device would have about 7 push buttons which when pressed data will...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
