Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I am experimenting with ENC28J60 and PCA10056. Following are my connections:
================= =================================== NRF52840 PCA10056 ENC28J60 (pin...
Hi
I tried to implement Eddystone example in nRF52810. it worked successfully. Then i tried to implement same in nRF52832 using pca10040. But it not working. I only changed...
Hi, I'm running the saddc_pca10056 peripheral example given in SDK v15.2.0.
The analogue pin A0 is connected to the signal line of an LM35 temperature sensor. When I measure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I am porting RTC example code as is into ble_app_blinky...
hi...
i want to advertise the multi link central example , i have added the advertising in code , now my central is advertising but when i tried to connect , i am getting...
I programmed a NRF52840 Dongle with the example light switch code having changed the channel to 14 which is what my coordinator is on.
I then programmed a NRF52840DK with...
Good day,
I program my nRF52-DK with BLE Eddystone example's pre-compiled hex:
\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_eddystone\hex\ble_app_eddystone_pca10040_s132...
my bootloader.hex is generated by "nRF5_SDK_14.2.0_17b948a\examples\dfu\bootloader_secure_ble\pca10040\arm5_no_packs", my app.hex is generated by a modified blinky example...
I am currently using nRF8001 in my board (configured to connect - send data - disconnect - sleep every 30s cycle time). However, I am measuring about 140uA in average and...
Hello there.
I'm developing a custom board for the nrf52810 chip. I'm taking the reference files as a base for my own design, but I'm a little bit confused on which files...
Hi,
I am using nRF52840, SDK 15.0, softdevice 6.0.0 (toolchain IAR 7 on windows).
My application runs on FreeRTOS 9.0.0 tickless (NRF_SDH_DISPATCH_MODEL 2).
I have a...
Hi,
I want to get Battery ADC Value.
So. I simply used nrf_drv_saadc_sample_convert() function.
At first I thought it was the right value,
Later, I found that the...
Hi,
I want to get Battery ADC Value.
So, I simply used nrf_drv_saadc_convert()
At first I thought it was the right value,
Later, I found out the wrong value.
If...
