Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,everyone
I want to add dfu service in UART example ,but when I tried to allocate the RAM,Debug terminal shows nothing,Then I set the breakpoint in nrf_sdh_ble.c and...
I am using Nordic SDK 15.3 and nRF52840 to interface to a NAND flash TC58CVG2S0HRAIG. I'm new with the SDK and I have little experience with the SPI / SPIM functions. I started...
Hi guys,
I use SDK14.2 (i can switch to SDK15.0 if it makes any differences) and would want to integrate FreeRTOS to my existing project. I have tried the FreeRTOS example...
Hello,
I need to measure battery on my nrf52 beacon. My input voltage is 4*AA batteries(each 1.2V so in total 4.8V). The schematic provided by the hardware developer is...
Hi
Am trying to implement the secure bootloader for the nrf52840 for Dongle,I have gone through the existing example for nrf52382 but am unable to find any example for nrf52840...
Hi,
I'm using 2 nRF52840 DK to run the Serial Interface example, please refer to the link
Serial ( named it as DK-1)
Light switch server (name it as DK-2)
And...
Hi all, I have custom boards with sdk11 already sold out now we need to update those boards from sdk11 to sdk12.2. so we are planing to update sd+bl image. The present sdk11...
Hello All,
I want to use SAADC with BLE working Mode. In my application, I will be using Image transfer Example for full blazing speed so I don't want to use any CPU resource...
Hi there,
I am trying to design a printed meander antenna for the nrf52832. For this purpose I copied the antenna trace from the usb dongle that Nordic Semi produces. However...
Hi, everyone
how to increase the peripheral link count in multi role lesc example . even i have tried with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT its not working
files.rar
Hello,
I am using nRF5 SDK14.1.0 and soft device s140_nrf52840_5.0.0-2.alph.I can program the board witt the bootloader(both pca10056 and pca10056_debug) successfully...
Hi!
I understand almost nothing about antenna design so I'm in general just copy and paste antenna design from reference board.
But this time I'm interested to make PCB...
Hello Nordic Support!
I ask questions after a year.
One year ago, I made a thermocouple thermometer using nRF52832. At that time, I encountered a problem that low current...
I'm working with the BLE experimental CLI example in the 15.3 SDK
I'm able to connect and read standard BLE services and characteristics, no problem.
However, discovering...
Hi DevZone,
I have problems with running the coexistence examples from the Mesh SDK. Specifically I’m most interested in the UART coexistence example ( https://infocenter...
