Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
hi attached code for below requirement:
command: scan on - scan devices
command: devices - display filtered devices .
Filters set are for : thermometer, NUS and custom...
I am using the TWI manager to schedule transactions with a number of sensors, over two seprate twi instances, and then sending that data over Ant.
The twi manager scheduling...
I am using the NRF52832 chip on a D52M M8 module, and SDK 15.2.
I have a number of sensors that I am communicating with over TWI using the TWI Manager on two separate channels...
Hey
I am working on ble_app_blinky central and peripheral, I want to calculate the RSSI of peripheral after connection with central. I am able to calculate the RSSI value...
At the end of last year, the new package nRF5240 WLCSP was delivered and it is now available in the market, however, I have not found an official layout for this new package...
I'm trying to use the QSPI periph to interface to a Flash, the project is based on the blinky and has UART and SAADC added in so far. I can use nrfx_qspi_cinstr_xfer to read...
Hello,
I am developing an application for location tracking to be run on a Windows computer. The computer will be communicating to a mesh network using the serial interface...
Hi,
I'm using nRF52840, with NFC pairing (based on SDK examples).
The problem is that sometimes, after advertising, my device is waiting and nothing happens. After using...
nRF52832, SDK14.0.0, S132v5.0.1
http://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Section 18.8 (page 83) shows that the WDT registers are retained across Soft...
Build and flash mqtt sample. Use board nRF9160. Ubuntu 16.04. Firstly flash secure boot, just after that flash mqtt sample. Have this in terminal:
The MQTT simple sample...
Hey everyone, I am trying to setup the external temp sensor instead of using the simulated data
I modified prj.conf to:
CONFIG_TEMP_USE_EXTERNAL=y
and Kconfig default...
Hello
I used the pc-ble-driver-py to advertise Apple ibeacons, but it seems that they're advertised as connectable undirected packets which is not good in my case, as...
Was told to avoid using nrf and particularly to mix nrf/nrfx functions.
Need clear sdk_config.h requirements to setup that also addresses what must not be in the config...
Hello to everyone.
I'm working with Light_switch example for nRF52832 (PCA10040) and Mesh 3.1. I'm trying to modify the server example and to do that I need to know where...
Starting from this example I try to bring clock functionality to my BLE-project.
1. The external LFCLK-XTAL
I need some clarification about the use of the different...
