Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello I am using nrf52832 and I want to Calculate date and time at specific event periodically and save it to flash,so is it possible by using ble_app_cts_c example or any...
as title,
I can't load the project to SEGGER Embedded Studio.
I can't install CMake by entering the those command ( choco install -y cmake --installargs 'ADD_CMAKE_TO_PATH...
Hi
I was trying to do the page up and down key, I just built it successfully but it is no response.
Could anyone find out the reason for me.
I appreciate for your assistance...
Hello,
I tried to follow the "nRF_Sniffer_UG_v2.2" and i didn't understand the section 1.2 which described how to set the Python and Pyserial,can some one explain what to...
Hi,
1. Can one run the coexist sample with softdevice S132 on a mesh where all the other nodes run S140?
2. does the coexist (UART) example need to be provisioned. ...
Hello to everyone.
I'm working with the Light_Switch example with four nRF52832 SDK (two clients, two servers) and my cellphone as provisioner, in Mesh 3.10, with "nRF Mesh...
Hi again, Figure 106 in the OPS indicates that the application core and the modem core in the nRF9160 have separate Flash and RAM partitions.
Is this a "real" partition...
Hello,
I ordered my nRF52 DK from Rigado for their BMD-350 module using the nRF52832 chip, but their DK comes with an additional Atmel chip. Now I saw the regular nRF 52...
Hello!
In SDK15.3 project "secure_bootloader_ble_s112_pca10040e" for Keil , write flash incorrect and not work.
In SDK15.2 this prodject work fine.
Please correct...
My application will update over USB from a connected host.
For testing, I used two projects:
Bootloader: secure_bootloader_usb_mbr_pca10056
Application: led_softblink_pca10056...
So im trying to interact with a nrf52 chip. I am using iOS corebluetooth to communicate with the device and when the device sends a long data packet (~400 bytes) iOS drops...
Hi,
I have my SAADC configured with two channels. One for my sensor and one for the battery level measurement.
I only need to measure my battery level every minute for...
