Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I implemented the app_pwm_library, but it seems to "top out" at 500Khz? Here is a summary of my code. Is there a set of routines that have a higher speed?
APP_PWM_INSTANCE...
Good morning,
I already made a nRF51822-based prototype some years ago, and now I'm working on a new prototype but based on the nRF52840.
Is there any AN like the nAN36...
The design I am working with has no RTC. Is it possible to use nrf_drv_timer to "wake up" the CPU? I understand I will not be able to use app_timer code, so I was trying to...
Hello,
I am trying to use an interupt from an analog devices ADXL343 accelerometer.
With a power supply of 3.0V to my board, I only get a 2.1V on the interrupt, and I...
Hello! What does the real marking of the nRF24L01 + chip look like? I have not such, but very similar. The problem is that the module after a while ceases to go to sleep,...
I am using a STlink to flash a nrf51822 module , and i am using Keil to do that, i flashed the module but when i am scanning it to find it in my mobile i cant find it, i doesn...
Hi ,
Does the Application update depend on bootloader version? . I changed the boot loader but application remains same on my device , hence the device is not booting up...
I have an application with three other tasks beside the sdh task. I'm trying to integrate softdevice to my existing freertos application, but soon after the task scheduler...
Hi,
What would be the procedure for updating the firmware of device through another host micro controller UART? (Not with PC tools like nrf go studio, nrf connect, nrf jprog...
Sir,
I have a MDBT50Q-UFL evaluation board. I am using Keil uVision 5 and flashing is done through ST-Link. I downloaded the example files from http://developer.nordicsemi...
Hi,
I have Ublox EVK-NINA-B3 on table, which has totally different pin layout than NRF52 DK (not sure why): https://www.u-blox.com/sites/default/files/EVK-NINA-B3_UserGuide_...
Hello everyone! I am a beginner and I need help in understanding advertising data. I am migrationg from SDK 13 to SDK 15.2. In SDK 13, the advertising data with manufacturer...
Dear Engineer,
work on sdk15.2, pca10040 eavl board. one as central run this code
\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\ble_central\ble_app_multilink_central...
I am starter developer of nRF51822 custom board.
in this board 16 mhz crystal is connected externally with XC1 and XC2 pins(37 & 38)
nRF5_SDK_12.1.0_0d23e2a rar file is...
Hello everyone,
I know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet.
For example: https://devzone...
