Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Good afternoon. I need to make a network 5 or 6 nrf52840 boards connected as peripherals on a single central board, also of nrf52840. Each board will read a sensor, and send...
because I cannot find nRF module for testing.
and I want to use bluetooth 4.0 BLE with nRF uart
so my product will send data from serial port (rx ,tx through DB9 ) and...
Hi there, We are not using external Crystal for this design and thinking of reusing XL1 & XL2 (Pin 0 and Pin 1) for SPI (MISO & MOSI). But I found that I can't set properly...
So we're in production with the '832 and me, I drank the kool-aid already, but I'm trying to turn my cow-workers on to Nordic so I tell one of them "Oh install the command...
Hi There,
HW: PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Test source code: ble_app_blinky
How can I create single Button with multiple condition based on the period of...
Dear Support,
I am working now on the PCA10040 Development-Board, I use the Booltoader from the nRF5_SDK_15.0.0 and the application from the nrf5_SDK_for_Mesh_v2.2.0. I...
Hi,
I have a crash in the LOG backend UART when the system shutdowns:
My power manager handler is as follows:
The crash occurs when the backend calls nrf_drv_uart_tx...
Dear Nordic,
I port one of my application for nRF52810 from nRF52832(application). i Followed as per guide. but when i build its showing an error.
RTE\Device\nRF52810_xxAA...
Hi, Sir
I met a problem when I enabled ble_adv_directed_slow_enabled in nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hids_keyboard\pca10040\s132
The detailed...
Hey all,
I've been having a problem that it seems like a few others have had as well. When I connect my desktop computer to the devkit, it does not respond to any nrfjprog...
HI, I am using NRF52832 sdk15.2 .
I have some doubts
How to assign two to three different timers to do different functions
1. I need to read the sensor data every one...
Hello,
I'm working on a BLE central project where we want to utilize LESC Just Works Unauthenticated pairing.
I followed the recommended usage guide at https://www.nordicsemi...
