Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi all,
I started a project on nRF52840 dongle with Segger IDE. I used SDK15.2 given by Nordic and my goal is to develop a program that permits to communicate between...
Hi,
Noted that nRF mesh app needs GATT bearer to provision a mesh device. I'm using 2 nRF52 DK boards, provisioning is fine, set the keys, subscription lists, etc, everything...
Hello, First of, I'm developing with eclipse an application based on the freertos example of the SDK 15.0 with softdevice S132 v6.0.0. My problem is that the nRF52 sometimes...
Hi. I have the latest topology monitor downloaded from the home page. It seems to have a problem. Every time i try to run it from my windows 10 machine (32 bit), it gives...
nRF TTM win32-x64 will not run on my PC. I use Windows 10 and am trying to run the executable but i keep getting "app cannot run on your PC. Contact the publisher....".
...
Hi. I managed to set up a mesh (Thread) using 9 nodes of the nRF52840 SoCs. I am currently using Putty to send commands and pings between the nodes. What i need now is a way...
Hello, another question from me :) First of all, I'm working with Eclipse, GCC compiler and SDK 15.2.0. I want to add GPIOTE funtionality to the TWI example of Nordic. I'm...
Hello there,
I've been struggling to find a way to read IMU values from my custom PCB. This PCB sends a notification as shown in this image:
My main objective is implementing...
Dear nordic,
i want to BLE+FDS application i have some doubts regarding this.52810 has only 192kb flash if i use both BLE application and FDS is it any problem occurs? ...
Hi,
We used nrf52832 in our custom pcb. It works.
NRF52840 has "Long Range" feature. We think, if long range needs in some application, we can set 8dBm output power and...
Hi,
I am using nRF5_SDK_12.3.0 and writing customized firmware based on uart example.
Everything works fine with the DK. Then I program the firmware to a nrf51822 module...
I have a DFU issue; SDK nRF5_SDK_13.0.0_04a0bfd
The system reboots on the DFUTAG after having completed the application upload.
I have the following errors : :DEBUG:Error...
Hello,
i'm trying to send string composed of three floats of an accelerometer measurement over BLE using UART nordic service (NUS),.
can anyone help me.
Hi, I got a very strange situation with Segger and the situation is:
When I add a sentence to see some info about variables with NRF_LOG_INFO I can debug the program with...
I am hoping to extend the battery life of the Nordic Thingy. Ideally a battery with about 10,000 mAh would be perfect. Is there a list of off the shelf batteries that other...
