We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
I am using nRF-Sniffer-v2.0.0.2 beta as seen here: https://www.nordicsemi.com/eng/nordic/Products/nRF-Sniffer/nRF-Sniffer-v2/65225 on a nRF52840 DK.
Wireshark Version: 2...
Hello guys,
I'm having problems with communication between a dwm1001 module (from Decawave) which is a nrf52832 board, and my Raspberry 3 Pi model B.
I have connected...
Hi
According to nRF52840 Product Specification, the SPI master data rate can be set in the SPI frequency register. The configurable values are listed there. Is it possible...
Hello everyone,
Maybe it is a stupid question but I am completely lost,
I have a stm32f103c8tb that I have to use for programming a nrf51822, the thing is I have absolutely...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE.
After pairing, the sum...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE. After pairing, the sum...
Hi
At the company I work for (Ztove ApS) we have expanded the capacity of nrfutil (https://github.com/NordicSemiconductor/pc-nrfutil) to include a option for AES (CBC mode...
Hi
In ESB there is the function nrf_esb_suspend(). After calling it, what function do I call to resume ?
Look forward to hearing from you
Regards
Mahendra
Hello!
Related to the addition of new services to the Attributes table, is there a way to check if a certain service UUID has already been added?
This problem arose because...
How do I check what version I have installed?
The 'Getting Started' page states a minimum version of 9 .5. 0:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
