Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
hi,
so i was coding my program with keil and it reach the 32kb so i had to move to the free IDE Eclipse. for that i followed this tutorial devzone.nordicsemi.com/.../
...
Hi !
I've seen that the Makefile given with the examples changed a lot between SDK11 and SDK12, lots of improvements ! However there's still something I don't get. Why...
What system resources are required when using GPIOTE channels (not the PORT event, the other channels)?
I remember on the nrf51822 there was a long-running PAN, fixed in...
I programmed nRF51822 with S120 softdevice and ble_app_hrs_c application to scan beacons.
It works fine but have one problem.
It scans beacons for about 10 seconds...
hi,
i am working on ble_app_uart_simple_adc example which is referred from the link github.com/.../nrf51-ADC-examples
i flashed the code successfully. and detecting the...
Running the SDK11 example \examples\peripheral\twi_sensor on a NRF52 PCA10040 version dev board and can't get any output from TWI pins. Leaving pins unconnected and using...
Hi,
I am trying to set up the development tools for the NRF52 on my Mac by following this tutorial aaroneiche.com/.../
I am getting the following error when i try to...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
Hello,
I have question, I'm actually developing an Android application and try to update the firmware on a device with a DFU process. It work on every mobile device except...
I am using the nrf51422 with softdevice 5144_2.0.1 ,
I set two network number using the "sd_ant_network_address_set" api , network number 0 for ANT+ cadence/heardrate.. network...
Hello,
I was just checking for differences between SDK v11 and v12, more specifically, the differences in the SPI HAL and driver code.
In hal\nrf_spim.h of the v12 SDK...
Hello, I am trying to write some data to the Nrf52, but all I get is a read only response on my phone. Is there any example how to write to the nrf52 tag?
