Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am encountering warnings while attempting to send Bluetooth notifications in my Zephyr-based project. The warnings are preventing successful notification of ECG data. Below...
HI ALL,
I am using v2.8.0, NRF54L15,and peripheral_uart demo has not made any modifications except for adding the following content. The test shows that the OTA upgrade...
1.test code
the code run separately on ble-softdevice and only timer demo .test code as follow:
2. test data
test result as follows：
picture A,show timer2 timing...
Hi,
I am using nRF Connect SDK v2.8.0 and nRF54L15-DK.
I am about to design custom hardware and have a question.
For Matter, I am trying to use the following pins for...
I am working with the unicast samples where one board is configured as a server and the other as client. Initially i had trouble installing the SDK, but it seems to be working...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.8.0. I want to create a DFU distributor that updates both Application core firmware and Network core firmware...
We have been porting from v2.5.3 to v2.8.0. So far the only thing that we've had to change has been the board files, but one thing that was noticed is that the CONFIG_FLASH_LOAD_OFFSET...
Hello,
On my Thingy:53, I would like to try Matter. I use Google Home to connect to Matter and I use the QR codes on the following page: docs.nordicsemi.com/.../README.html...
I need to build a PC-based workstation (Windows 10) for programming our boards that contain a nRF52840. Do I need to download / install the command line tools and the nRF...
I'm trying to update the modem core from the standard firmware to the production test image on my nRF9161 dk to experiment with the PTI before doing the same on a custom board...
I'm using firmware 1.3.6 and SDK 2.7.
I have a ppp connection problem for IPV6. Tables below show connection status:
When I use SLM:
ISP / PDP + APN
"IPV6" ...
I read some previous posts that there was limited support for sysbuild for the VSCode extension. There are two things that I noticed: 1. When creating a build configuration...
For a project i need to use the channel sounding feature of bluetooth. On checking samples on nRF Connect SDK couldn't find any examples. But the Zephyr project is providing...
I run a matter light_switch demo on my nrf54l15dk board, and I added these two configurations in prj.conf to enable dfu over bt smp. Built and burned the firmware into my...
Hi,
I am currently working on creating a Custom Profile, and have used Peripheral Sample code. I tweaked the code and was able to send 512 bytes of data on 8 different characteristics...
