Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi
I have currently claimed devices in my nRFCloud I registered two years ago. It looks like this:
It has the mention "powered by memfault" . This is also the nRFCloud...
Hi,
i'm learning l4/e1 and i'm trying to buid the process after finishing step 10 but the build didn't goes through successfully. i got this errors
my SDK & toolchain...
Hello all,
I have an nrf54l15 on a custom board, I am having issues getting a reliable SPI clock signal when using BLE advertisements
This is the clock and correct...
I bought both nrf52 DK with nrf52832 and ISC-nRF52810-A module. I use Visual Studio Code with nrf SDK + toolchain. Hardware connection from ISC-nRF52810-A to nrf52 DK is as...
The openthread coprocessor sample in sdk v2.8.0 and v3.1.0 work for me with the openthread border router but not the sample in sdk v3.2.1
I followed the instructions for...
Hi,
i'm learning the exercise1 for AT commands to control modem and when i apply this command AT%XMONITOR i get the output as %XMONITOR: 5,"","","24202","0901",7,20,"02024720...
nRF52810 program execution failed the CPUID verification. Hi everyone, I have a question. I have a working PCBA with an nRF52810 as the main controller. When reading the CPUID...
I have a simple project running on a custom board with a nrf54L10 processor. The board has a couple of LEDs to blink and advertises on BLE. With v4.3.0, the LED blinks for...
nRF54L10 + NCS 3.02
A simple question: So I found CONFIG_MCUMGR_TRANSPORT_BT_DYNAMIC_SVC_REGISTRATION=y which lets me enable/disable the SMP service. Is there another config...
I am using nRF5415-DK and SDK v3.2.2
I want to generate a sine wave using PWM and TIMER. The PWM repeat duty cycle method has limitations, so I am using a timer to trigger...
Hi, for one of our products we are evaluating an option of porting the application from nRF5 SDK (nRF52) to nRF Connect SDK (nRF54). Seeing the similarity between the nRF...
Hello DevZone,
I am currently trying to fix an issue I have on deployed devices, using nRF9160 with nRFCloud. Code is based on SDK 2.8.0.
In most cases, my code works...
I am attempting to use the nRF52840 QSPI periphery to communicate with an SRAM chip. The chip is IS66WVS8M8FBLL-104NLI. I am unable to communicate with it using QSPI. I am...
Hi everyone,
For mthe prject I'm working I must use the LPCOMP module to detect a cross. but anytime a init the LPCOMP module my code seems to freeze and nothing else...
Hi,
I have developed a Matter-over-Thread light bulb using the Silicon Labs EFR32MG24 platform, with CHIP_CONFIG_SECURITY_TEST_MODE = 1 enabled. In parallel, I have set...
