Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear Nordic Engineers, This Pham Tuan Kiet, RnD member from HTSC company. I am currently testing asset tracker v2 on nrf9151 dk. I am having problems with registering the...
Hi,
We are currently working with the nRF5340 Audio DK board and aim to implement Bluetooth Low Energy (BLE) message transmission alongside the existing LE audio transmission...
I am trying to debug a BLE application on the nRF52840 DK. From what I understand, this must be done in monitor mode.
I have followed these steps:
1) added these lines...
Hello,
Hi I m trying to implement the following using mcuboot and zephyr. I have a nrf52840dk which has a external flash mx25r64 to store multiple images on the external...
Hello. I am reading up on documentation regarding measuring current on the nRF54L15-DK with an ammeter. I do notice that when we set up the board, we need to use the 2x5 SWD...
Hi there,
I attempted to change the nRF54L15-PDK settings in Board Configurator. I disabled VCOM0, VCOM1, Power to LEDs, Software Debugger and set VDD to 2.0V. I have...
Hi all,
I am working on nRF-9160 and nRF-9151, and I wanna know does Serial LTE Modem support will message function for MQTT connection or other connection?
I've asked...
Hi,
I am not familiar with the 9160DK board. I followed the same steps as the nRF Desktop Connect application guide but it always shows verification failed. I am using my...
Hi
I'm having an intermittent connectivity issue with the nRF9161 where after days of operation the device loses cellular registration and fails to reconnect.
The...
Hi,
is there a way to hide the west project from the Git view in VS code? Sometimes you just don't need to view any changes related to west and it's getting quite messy...
I am working on a Zigbee network using the nRF Connect SDK and need to retrieve the link quality information (LQI) of a specific device based on its short address. What ZDO...
Hi,
I have used nordic documentation a lot few years ago, and I am looking for BLE sequence diagrams especially the ones during pairing process with LE Secure connection...
Good morning,
currently we are on ncs SDK v2.7.0.
Because SDK v2.8.0 supports the KMU in MCUboot on the nRF54L15, I updated immediately and gave it a try.
Unfortunately...
Hello,
I searched but I can't find how to retrieve accelerometer data with thingy:53 and then send it via bluetooth to nRF Connect on phone?
Can you help me
Thank...
