Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
Hi,
I am developing a product based on the nRF9160 using the LwM2M client. I successfully have this working using PSK, but want to use X509.
I am calling lwm2m_security_set_certificate...
I'm migrating our project with custom boards from NCS 2.6.1 to 2.7.0, and I'm having a number of issues in the vscode extension (v2024.9.87):
The "Create a new board"...
Hi,
We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB.
Do you have any reference designs for a PCB antenna which must be as small as possible...
Hi,
I'm getting an error when building the example temperature that says: Linking 'temperature_pca10040.elf' cannot open output file C:/Users/임선영/Documents/SEGGER Embedded...
Hello,
I am designing a LTE-M GNSS Tracker, that should also be able to scan for WIFI APs. I dont need to use LTE and WIFI at the same time, but rather like that:
Connect...
Hello,
I accidentally programmed BLE firmware onto my Power Profiler Kit 2 (PPK2) , and now the device is not recognized. Here's what happened:
I first opened the NRF...
hi support team,
customer had one problem about "AT%XCBAND=? "
fir st. Customer try to set catm and catnb systemmode together as below, i could not see the band17 in list...
Hi.
We are using NCS v2.6.0 in our application and migrating it to v2.7.0.
In v2.6.0 we have used child/parent image for MCUBoot. We are using the same application firmware...
Hello,
I know that maybe you won't be able to help but i'm giving it a try
I'm trying to use enc28j60 connected to a nrf52840. I saw these example https://gitlab.com/enc28j60driver...
Hi,
I am using a NRF9160. I would like to use nrfx_timer with a base frequency of 32MHz with the TXCO as clock source.
I saw in the documentation that timers use the base...
Hello DevZone community,
I have been using the lte_lc_conn_eval_params_get() function in my application, which is executed periodically.
However, I'm encountering an error...
Hello,
My goal is to combine the Peripheral UART sample code and the LSM6DSO I2C sample code with the objective of sending data from the sensor over bluetooth. Based on...
