Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello,
We are in process of FCC certification and we would like to use LTE and Bluetooth Coexistence to reduce number of measurement needed for the certification.
We are...
Since several weeks, the NRF Connect for Deskotp's programmer application (v3.0.4) is stuck in an infinite loading loop, as was the toolchain manager previously ( see https...
Hi,
I am working on a project in nrf connect sdk v2.0.1 central side using nrf9160dk_52840. I want to pair my peripheral device with this central That is possible. Please...
Hi,
I am beginner with NRF52840. I want to create a task scheduler using multiple tasks with different level of priorities that is low, medium and high. I am using SDK...
Hello,
I got two PCA10056 1.0.0 DKs equipped with an nRF52840 rev. 1 (code AC0). Both do not measure the VCCH voltage correctly (displayed voltage ~2.4V instead of 3.0V...
This forum feels pretty advanced, so if this is the wrong place to ask this question apologies and please let me know where I should be asking it instead.
My goal is to...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0, with updated MDK (see link )
IAR EW ARM...
Hi Everybody,
I need help in writing a little software on NRF52805 which will active the transmitter with parameters:
1) Frequency : 2402Mhz only. (and i will later...
Hi,
I'm using nRF52832 with S140 v7.2.0 base on nRF5_SDK_17.1.0. I use PCA10100 development kit and set VDDH/5 as input and use internal reference (0.6 V) to do the battery...
Hi
I am working on SPI implementation on BL653_dvk board and while SPI_transfer i want to capture the timeout error.
but not able to differentiate which timeout is correct...
Hello,
We are using MDBT42Q-512KV2 module which is based on nrf52832. There is Central and peripheral ( Foot Pedal Switch ) using same module.
We have used crystal from...
I know from the product specification for the nRF52832 chip that the high frequency clk can use a external 32 MHz crystal as source. My question is, is it possible to supply...
Hello!
I am now developing a product with NFC based on nrf52833.
I need to transmit some crucial data between device and phone, such as device settings.
But I have...
Hi all,
I would like to measure time intervals between gpio edges along with Matter.
I tried to use a 100us timer interrupt but seems it will crash the original matter...
Dear Support
I have made the following findings of my evaluation of the NRF5340 with Version 2.1.0 SDK:
-CIS mode has no constant delay at default settings 48-4. According...
