Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi, I have an issue when I try to install the nRF connect SDK. I am using Linux Fedora 39, trying to isntall SDK v2.5.0. Steps taken so far:
Download and install nRF command...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
Hi,
I am having problems getting PSM mode, or at least getting a decent power consumption in PSM mode, because I think the PSM in working properly.
I am using the EVB...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
Hi,
I am currently working with the nRF5340 Audio DKs and have successfully implemented the gateway and handset functionalities.
Now, I want to extend the system by enabling...
With the mcuboot enabled, I'm not being able to disable the boot banners even by doing the below settings in prj.conf file.
CONFIG_NCS_BOOT_BANNER = n
CONFIG_BOOT_BANNER...
Hi!
In our project, we need to send cloud-to-device commands. By "command" I mean a request to do some short action, not a request to change device's configuration/state...
Dear Nordic Team,
Today, as of January 30, 2025, our devices started giving the same error and we are no longer able to receive any location data from nRF Cloud and even...
Hello,
I'm currently working on a project that uses the PMIC nPM1300. We need to monitor the battery's SOC, capacity, etc. As far as I understand, I need to use the fuel...
We have a number of graphical assets that are taking up a significant amount of flash space on the nrf52840. I would like to use memory external flash over QSPI to store the...
Using the LVGL sample... The sample LVGL code works on nrf52840dk but not the RAYTAC MDBT50Q . I hope I'm just missing something obvious?
Flash blinking to nrf52840dk...
Hello !
I am using using the chip BT840F of Fanstel (based on the nrf52840) powered by an external 3.0 v battery for my beacon BLE application.
Regarding power consumption...
