Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I2C burst write for nRF5340 at 100kHz is failing with a reply of -5. (Trying to use the BMI270 drivers sample, it will fail during reg_write of the configuration file)
Reading...
hi
I have nRF9160 dev kit, which I am using in a LAB with a private LTE SIM card, which has 99920 PLMN ID.
The network supports Band 3, and NB-IoT is configured as an...
Hello everyone,
1st of all, thank you for taking your time to have a look over my "problem".
I have a device that I am working on, that acts as aperipheral, it is...
I modified, My application's bdaddr is set public device address. secure bootloader's bdaddr is set same public device address.
When run DFU on nrf connect for desktop,...
In my application, I am unable to read back the publish address which was configured during initialisation through mobile.
Please suggest any APIs.
Device: nRF52832
...
HI
The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" and I find a question that is: for all thread programs, add nrf _ delay_ ms () function in while (true) will affect...
I use a sample in NCS1.5.0 to start my project . but examples in NCS1.5.0 are single ble service .always like these: bt_conn_cb_register(&conn_callbacks); bt_enable(bt_ready_cb_t...
Hi,
1. I see the following differences between VDD1 and VDD2 descriptions:
nRF9160_PS_v2.0 P385
2. What are the differences between VDD1 and VDD2 features?
Thank...
Hi all,
I am trying transition from SDK 15.0 to 17.2 and having a branch instruction to itself (an infinite loop) which I think has something to do with the adjustment of...
I would like to create SPI clock timings using the following documents. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fspim.html&anchor=topic
1. CSN...
I'm trying to figure out a strange issue with GPS. We have a pretty well debugged and stable system that we're adding some features to, mainly GPS. We're on SDK 1.5, using...
Hello!
I am developing an application which is connecting to an nRF52 board using the Android-BLE-Library implemented by Nordic The application is doing the following: ...
I was looking at nRF52833 as a candidate to use it as a BLE keyboard and USB keyboard (as it has USB2.0)
But in the API documentation section I see that HID keyboard is...
Hi,
I am developing a product using HA.
I am using SDK 3.0 and nRF52840 Dev-kit.
I am using the thermostat cluster, basic, time, power config, and OTA.
Along with...
Hi Devzone,
I use the original MQTT_Sample example, just change "Client ID", "Alive Time" = 120s, use NBIoT + GPS.
Development set up:
ncs v1.5.1, ubuntu, thingy91 ...
