Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi nordic
I run the HID keyboard with SDK 15.2 and connected to IOS's nrf conncet.
but i can't see the HID service in the table.
how can i use the nrf connect to debug...
Hello there,
I'm ripping my hair out hear reading everything I can to get the non volatile memory reading and writing.
I have a nFR52840 dongle and I dont want to...
Hi everyone,
I have a project that needs to use multiple saadc channels but I don't want to use ppi but use app_timer. So is there any way I can change between saadc channels...
I'm using a timer to trigger pins via PPI & GPIOTE. Setting the PPI TEP to the GPIOTE task works as expected. However, when I try to set a second pin via GPIOTE task via PPI...
hello Nordic
i am working with nrf52832 soc with SDK 16.0, S132 V7.0.1
following this path:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hey,
There is a microSD connector on the bottom of the nRF9160DK (v.1.0.2). Is there a way to utilize it as an external memory? I can't find any information about it on...
Hello,
I've been studying Bluetooth technology for a few weeks. I wanted my first to implement a simple key finder device, as my first project. I was doing some research...
Hello, For our nrf52832 custom board developed using nrf SDK 14.2, I need to turn OFF and ON LED accurately in terms of ms, hence after going through this page, I used Single...
Hi,
We are developing a device that should work in multiple mobile networks, and some of these are known to provide no DNS server. As using a fixed IP address for our cloud...
Hi,
I want to read the data from the a cceleration sensor by I2C. Several days ago, I added the code about twi bus to "ble_app_template" example , it worked well. But today...
I have a custom board, I am using to evaluate nrF52811 from eclipse (I just prefer this over SES).
I have installed S112 on the flash and also my application at 0x19000...
I'm communicating with N25 flash memory, the page size is 256 bytes. there is a page_program command which can write up to 256 bytes. there is no way to write in the middle...
Hi I'm trying to change peripheral usbd_ble_uart_freertos example to central with nus_c I added the scan and nuc_c module. When I'm testing the application, before making...
Hello, I am using:
NCS v1.5.1 and the sample code from ~/ncs/v1.5.1/zephyr/drivers/sensor/max30101/ (max30101.c, max30101.h) nRF5340dk MAX30101 from Sparkfun www.sparkfun...
I suspect this is related to https://devzone.nordicsemi.com/f/nordic-q-a/36601/gpregret-and-nrf_bootloader-c-evolution-proposal (Case ID: 211047)
In nrf_bootloader_info...
