Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I have a project from 3 years ago (2018) that I'm trying to make a simple update to the application code. The code downloads via the Segger Embedded Studio and runs correctly...
A vulnerabilitiy in BLE secure connections is reported as CVE-2020-26558 : Impersonation in the Passkey entry protocol
"The Bluetooth SIG is recommending that potentially...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
While following the steps required to provision the nRF9160 Connect for Cloud certificate, I entered the 'AT+CFUN=4' in the AT command text field and I clicked 'Send' but...
I have a working code using SoftDevice 140 7.2.0 and Segger ES on the nRF52840 DK. I made the single adjustment of the preprocessor variable BOARD_PCA10056 to BOARD_PCA10059...
Hi,
I use example projects from Nordic Thread: CoAP Client and Thread: CoAP Server with Segger Studio Nordic Edition (projects use Zephry which is generated by NRFConnect...
Hello! I`m developing custom board with NRF52832-QFAA on board and need to use serial bootloader. As in example (secure_dfu_ble_s132_pca10040), I`ve implemented it on board...
Peripheral doesn't have any user interface that can be used for pairing and bonding but I want for my application is that the peripheral gets paired or bonded to the central...
I want to make one mesh beacon as a node of mesh network.
If one mesh beacon is a node of mesh network, I want the beacon broadcast the messages which in mesh network to...
I build some test project in Zephyr examples folder. (ncs\v1.5.1\zephyr\samples\basic\ND_test).
In additional I did some changes in the Zephyr project in drivers and added...
I have recntly purchased a Nordic Semiconductors nrf52840 development board. I am having issues with the J Link OB MSD. When connected to LINUX Ubuntu 20.04 LTS which is running...
Hi,
I am working on a bootloader that can do DFU for my nrf52840 DK. Currently, when the bootloader goes into DFU mode, it obtains the init packet via UART. Then, after...
