Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d.
I'm trying to get NVS working using /zephyr/samples/subsys/nvs. It is failing to write. I also tried the code in this post...
hi
i was trying to interface sd card with nrf9160 in segger emstudio. i was following the ticket Reading SD card on nRF9160dk - Nordic Q&A - Nordic DevZone - Nordic DevZone...
HI sir i was trying to interface pdm microphone. i followed the existing ticket PDM Driver for Zephyr on nrf52840 . i had modified the proj.conf as below
but during the...
I've created a peripheral that is advertising about every 320ms but am seeing less than half of those packets in nRF Connect on my Android mobile (configured to run in low...
Hi, Could you please guide me on how to fix this? I've ported the slm client example here to the bsp project inthe sdk and getting this `.nrf_queue' will not fit in region...
I have an input signal of unknown period and pulse width on a GPIO. I want to use the PWM capture capabilities to retrieve those parameters.
I see in the documentation there...
In my quest to gain access to the nor memory on the nrf9160-dk I have found what happened to the WP and HOLD signals and now external_flash_pins_routing configuration setting...
Hi,
When I plug in my NRF51 Dongle it shows up in Windows explorer as additional drive (JLINK). Can I use this medium to configure my application? Can I read a file pun...
Hi,
I have a small pcb project with low power bluetooth IC NRF52832. There is a limited space on PCB so i decided use the 2.4 GHz chip antenna. İs there recomended chip...
we have deploy the serialization libraries in our host to communicate with nrf52840, but it seems the serialization libraries don't handle pairing/bonding event, so we can...
So I am doing a number of crypto operations. One of which for example is an ECDSA signing operation. I do that through mbedtls_ecdsa_write_signature which is using the CC310...
Hello,
We're currently evaluating the feasibility for leveraging our existing NRF51840 as host/system processor that runs all of our application code and runs the BLE...
Hi,
I am having some trouble. For a project, I need GPS, 9 axis IMU (accelerometer, gyroscope, and magnetometer), a microphone, and LTE connectivity in a small form factor...
Hi Team,
I am using nRF Connect SDK v1.3.0 tag for nRF52840 DK.
I am trying to integrate BLE HCI UART project files into Zigbee light switch project.
I have attached...
