Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Nordic team
Current https_client example at sdk connect
Connect to server --> send http request to server --> Wait response from server
Can we receive packet from...
Hello,
After a long investigation I got to the conclusion that SPI master (spi3) has been broken in the SDK version 1.4.1.
It is working fine in V1.3.1
I have an application...
Hello,
I'm using SEGGER Embedded Studio 5.30a with NCS 1.4.99.
I'm trying the "hello_world" sample but when i want to run on the nRF5340DK i get the followings errors...
Hi,
I am using FDS for read and write the records with SDK17, My code is working fine but when I change the optimization level 2 for size then I am getting FDS_ERR_UNALIGNED_ADDR...
Hello everyone,
I'd like to perform a DFU through the USB port on my custom NRF9160 board (DFU over UART) using the NRF Connect Programmer App.
I already did the Firmware...
Hi,
I'm using NRF52840 to connect with a mobile device.
During the connection, I have random disconnection with the reason code BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Excuse me, I want to download the nRF52810 reference layout on official website, however I can't find it.
Could you please send a nRF52810 QCAA reference layout to me
When the nRF is connected as a peripheral and no data is transferred either direction except the empty packet every connection interval, does the power consumption increase...
Dear,
I tried to make a copy of the Asset Tracker example application to start my own project. i gett this error
create_nordic_project.py failed
Creating solution...
Hi I am using the latest SDK for Mesh and also the latest nrf sdk. Downloaded and installed both last week. I have written an application that is derived from the light_switch...
Folks,
We are working on a custom design where the STM32L4 (external host MCU) talks to the nRF9160 over an UART connection to transmit sensor data. When the sensor data...
Hi,
I'm use nrf52840 with Light switch example of nRF5 SDK for Mesh v5.0.0 . Could I modify the packet of network layer ?
I want to add 2 bytes of UUID in the packet...
Hi, I want to add compression libraries like lz4 and audio compression to my zephyr projects. I am struggling to find good guides on how to add external/third party libraries...
Hi,
I have a nrf52810 board working as a peripheral, I want my board to connect to specific central application to protect it with malicious attack by other devices.
Please...
An error occurs when you run the following program(main.c).
[1;33m<wrn> bt_hci_core: opcode 0x2006 status 0x01 [1;31m<err> LOG_MODULE_NAME: Advertising start (err -5)
...
