Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I have a project that uses several protocols, including UART and USB CLI
As such, I had to move the nRF logger to work on RTT, so that everything could work properly...
Hello,
I was wondering if it is possible to read the model (e.g. NRF52810_xxAA_REV1) from a chip with nrfjprog?
In production we use nrfjprog to program our devices and...
Platform: pca10100
SDK version: SDK17.0
Purpose: Use radio to scan Bluetooth devices and perform CTE sampling. When the scan data and IQ data accumulate nearly 4K, output...
I'm using a 52840 and need both low stand by current and use of a UART. I understand that the UART drives up the power so I'm trying to completely shut it down when not being...
Hi, everyone
I am studying openthread.
I had a nrf52840 Dongle(running CLI/MTD example) act as MTD node to join in the openthread network.
The Dongle's LEDS were removed...
Hello,
I am using a nRF DK (nRF52832 - PCA10040 - SDK 15) to communicate with a custom electronic device developed by my own company (which integrates an 1-Wire slave)....
Hello,
I have a question regarding eDRX mode on the nrf9160 in combination with NB-IoT. I tried to configure an eDRX cycle of 20.48s for the use in a battery powered actor...
Hello,
I am using the nRF52832 on a custom board, with SDK 15.2 and SD132 v6.1. My BLE application uses the SAADC to measure VCC voltage every 6 hours. I am using an app...
Hello Sir,
I am Working with nRF52 DK Development board. My application based on BLE. I want BLE stack for Scanning mode and also tell m,e how to operate with mobile apk...
How to
1. increase advertising frequency - Which BLE GAP parameter should be updated?
2. increase RSSI signal strength - My device is not battery operated, so there are...
Hi,
How can I make the modem start a hot fix after rebooting the nrf9160?
I am getting a GPS fix, then powering down the modem with CFUN=0, which should be saving the...
Hello, I recently bought a nRF52840 with the intention of using it as a substitute for UART wired communication. What I want to do is send and receive messages between my...
I carried out following steps:
Application was using SDK 11.0.0 for nRF51 SoC
Ported SDK version 12.1.0
Using secure DFU boot-loader from SDK 12.1.0 (followed all...
Hi,
I understand I shouldn't use S140 v6.1.1 with SDK v17.0.0, but we want to try to keep using v6.1.1 as it's been well tested. Since the ATT_MTU example works with this...
Hi, im trying to gather accelerometer data from Mi Band 3.
I found script, written in python, that allows computer with linux to connect to band. But its missing functionality...
