Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
Hello,
When I try to run a project containing a .cpp file, I get the following console output:
I am compiling the openthread client example with a slight modification...
Hello, I am trying to change the instance on the spi in the spi example, but unfortunately it is throwing me an error - implicit declaration of function 'NRF_DRV_SPI_INSTANCE_...
Hello,
I am using nRF52840 S140 v7.0.1. I have a query on Tx power settings.
1) In below snapshot under features, its mentioned as “4 dB steps”. So whether can I write...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
We have v0.8.2 of the nRF9160DK which has GPS antenna issues. We are looking to get the latest available version of the DK from Mouser/DigiKey. Is there any way to ensure...
Hi,
I want to use SPI to receive data from an ESP32 microcontroller to the nRF52840 development kit. Where can I find information/example regarding the same (I'm using nRF_SDK_17...
Hi
we have a custom board with nrf52810 chip, 32M crystal on it and using the zephyr version 1.14.1 as the firmware base.
Using zephyr samples/bluetooth/hci_uart
Custom...
Hi Sir,
We design the nRF52810 in an embedded system and plans to use BlueZ to control the BLE device.
We can work with nRF52-DK through HCI_UART, so w e also implement...
Hi There
More recently, I have implemented the experimental of nrf52840 Dongle ,which is about Er asing it with nrfjprog or programming it with SES by DK. The dongle will...
