Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
By taking CLI as reference: added end point handlers, changed flash placement file with zb_ep_handlers.
Issue facing was:
ZB_ZCL_CMD_REPORT_ATTRIB command is not at all...
Hi,
I have nrf52840 with softdevice and i want to write 12 byte of data at a time in internal flash,suppose i write 50 records and i have to also read it these data from...
Hi.
I am familiar with Nordic NRF51 and NRF52 as I developed OpenSource firmware for chinese ebike displays with them and using the provided examples for UART Bluetooth...
Hi,
I am trying to understand the different PHY modes available in nrf52840. What are the differences between nRF 1Mbit and 2Mbit proprietary modes when compared to BLE...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
Hi Team,
We are using nrf9160-DK. We have tested assert tracker application, where we got the real time GPS data(DK location) we are happy with that. We also tested the...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Environment :
Host : Macbook Catalina
SDK : 16.0.0
Toolchain : ...2018-q2... (the pre-configured toolchain in the SDK)
SoftDevice: (not used yet, planning to use...
Hi, I'm using mesh_ SDK and nrf52840, I want to know whether the relay node in a BLE Mesh can wake up at a specified time to receive or send packets, and sleep the rest of...
Hi,
I am developing a device based on nrf52840 soc, and the rule of my device is peripheral. I want to know, if a connection was established, could my device start the...
Hello,
we are currently in the development of a low power, battery powered device that needs to count slow pulses (period between ~10ms and several seconds).
At the...
I have a custom nRF52840 board that transmits sensor data (using UART) to a PC with an embedded Bluetooth adapter. I have a code on Matlab that works just fine (using blelist...
Dear Sir.
I am using Master SPI to drive 2 slaves.
Both spi are referenced within Interrupt routine ,
When both spi;s slave are referenced I get an error
err = spi_transceive...
