Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
From the documentation i have found it seems all the nrf52 and the new nrf5340 are all "extended range" up to 105 degrees celcius.
I am evaluating an application where a...
Hello!
Thanks for your help last time, highly appreciated.
However I haven't got till actuall programming because now I can't upload hex files. I start Thingy:91 in boot...
Hi guys,
I just started to work with Nordic boards and I am currently working with Nordic nRF52-DK. I have already installed all the necessary tools that I need to run and...
Hello,
I've been playing around with the nrf52 DK (sdk 16.0.0, s132). I'm trying to add volume up/volume down functionality to the example. I found this source code from...
Hello,
Does anyone has an example of MQTT LST application for nrf9160.
I've tried to use the MQTT_Simple sample with LST.
I've add "CONFIG_MQTT_LIB_TLS =y" change the...
Hi everyone,
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840 SOC.
The system will operate in normal voltage mode (VDD = VDDH...
Dear All,
I am trying to compile a project from the command line and I want to enable all the warnings possible for the files that I have created. I am using the NCS v1...
hi support team,
i tested the example of \\nRF5_SDK_16\examples\peripheral\usbd_msc , and SD card interface , that with the APP_SDCARD_FREQ_INIT 268435456 (1 M) and APP_SDCARD_FREQ_DATA...
Hi DevZone,
I created my project on SES in order to download files from a web server. So I decided to include in my project the "download_client" library which contains...
Hello! I am working on updating from SDK 15.2.0 to the SDK 16.0.0 and have encountered some problems when trying to use DFU OTA to flash my unit with the application.
I...
I need to be able to measure the battery level of the NRF52 with the internal ADC.
I know it can be done, but I don't really know how to configure it
I am using MBED...
I have purchased an nRF51822 module. I am using the Arduino IDE and the ST link to program the module. I have used the library BLEPeripheral by Sandeep Mistry (see below)...
I deleted a node in the mesh app without unprovisioning the node. I then reprogrammed the dongle hoping that everything will be reset. It seems the dongle is still provisioned...
