Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I use nrf51822 to do bluetooth keyboard, I hope the function is: I want to change the IRK value of the bluetooth keyboard each time it is paired and bound,Anybody know how...
Hi can somebody help why nrf52840 doesnt be reseted when you press SW5(if boot/reset)? I have alredy with tried with few examples flashed on nrf52840 and in Segger IDE set...
Problem :
I have two I2C devices and would like to connect them both to nRF52840 DK on different I2C pins. According to datasheet nRF52840 has two I2C pins (P1.00, P0.22...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am trying to build out a button pressing scheme for BSP on a custom device with 15 buttons operating on a BL652 Laird Module (underlying nRF52832). After modifying...
I'm working with the NRF9160 DK and have found the sample times for the ADC to be abnormally long. I am sampling three channels and seeing a total time for the ADC read of...
Hey guys, I am using 2 nRF52832 boards with a PCA10040. I program my boards with the BLE UART central and peripheral examples. I was wondering if it is possible to, and if...
Hello,
I used 3 nRF52-DKs to run the pb_remote and it ran well with the Mesh SDK v0.10.1. Then I created my own project and copied the code from the pb_remote client and...
Hi,
I'd like to test the sample udp_gps but SES throwes an error and a warning. The warning says: Path/udp_gps/prj.conf:36 warning: attempt to assign the value 'y' to the...
I'm attempting to use the serial DFU bootloader to update my nRF52832 firmware but am unable to. I started by following this guide though I changed some things so that the...
Hello,
Let me introduce you to the issue:
I am working on a custom firmware for a custom hardware, based on the nRF52832 and SD S132, as a central which need to connect...
Dear Nordic Support,
When I got my nRF9160 DK, I ran the getting started successfully then I followed the instruction from the 2 below links:
https://devzone.nordicsemi...
Hi
I have an issue with updating DFU by nRF Connect on iOS 12. I receive the error:
Although it is working on Android without any problem.
I am using softdevice 6...
During WDT implementation I went into flash loader problems.
It is not possible to start a new debugger session (flashing) and the system is stopped at the progress bar...
