Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
If a rf52 device running ESB in RX mode has multiple devices TXing on different pipes, is it possible to prepare a different TX response to be sent to each device...
As the title suggest, I am running into an issue where my nrf51822 bluetooth keyboard is drawing around 8mA, which I think is way too much.
I am using gazell protocol to...
Hi,
My architecture is as following {CPU <-> nRF52840 subscriber <-> Raspi + nRF52840 Gateway <-> nRF52840 publisher <-> CPU}
I am working on Paho MQTT-SN programs, and...
Just want to verify that would be possible to run TCP Socket over with the nrf52840. And if i can be pointed to the specific links that i can use.
Thanks!
Hi, I am in the initial stages of starting development with nRF9160-DK. At this step, the LED 4 on the board absolutely does not blink. I have tried taking the kit to different...
Hi, some questions regarding BLE
Is merging multiple Characteristics into a single service make discovery and connection faster? And why exactly?
If all Characteristics...
Dear Nordic,
I have noticed that the USB CDC exemple stopped working on my nRF52840.
It seems the event APP_USBD_EVT_POWER_READY is never received by the application...
Hello,
This is my first experience with any nRF hardware and programming using BLE. I want to program my nRF52 development kit over the air from my windows computer via...
Hi,
I tried to use BLE DFU with nrfutil on my nrf52832 custom boards, but always get the result of 'Failed to open. Error code: 13', so I am trying to build the connectivity...
Hi,
I am trying to run the NRFX_SPIM example project code on my DK. But my DK is 10040/nrf52382 and the example project given in SDK15.2 only has a folder for 10056. Should...
Good morning
I'm new to these SoC systems, but I've developed a custom board with the nRF52810QCAA chip and I'm using the example (ble_app_eddystone) of the SDK15.2. softdevice...
Hello
I am now using nrf52832 and BLE communication with an Android terminal.
BLE communication is a beginner.
I am using nRF_SDK_15.0.0_a53641.
Since I programmed...
It seems possible, but I can't quite figure out how to use nrf_ble_scan_filter_set to use more than one device name. Any assistance? Alternatively, is it possible to use wildcards...
Hi,
In GATT level, on the receiving side - Is it possible to receive a corrupted packet or does the LL identify and discards such packets?
Specifically
- Will host...
Hi
I segger project get compiled and download successfully but it didn't start work. After put it in debug mode, it start working even after removed it from debug mode working...
