after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi ,
I am running example in nrf52840 using segger embedded studio .
And i am trying to define __no_init variant ,
May be sameone know what is the syntax . in IAR __no_init...
Hi all,
I am building a demo for Bluetooth mesh networking with thingy. I had followed the instructions under this link:
https://github.com/NordicPlayground/thingy52-mesh...
Hi,
I am using the twi_sensor example in the board PCA10056 with SDK v15.2.0. I am trying to disable the internal pull-up resistors of SDA and SCL lines to use external...
There appears to be a design flaw in the nrf_sdk_freertos code that produces a race condition. The race condition can result in a delay in processing a SoftDevice event, or...
When setting up Heartbeat Subscription for a node, a single unicast address is specified as the source. Does this mean that a node can only subscribe to heartbeat messages...
Hello, I am using nrf52 with sdk 13.0.0. Bootloader_secure_ble gives error while compiling. What should I do ?
Error[Lt009]: Inconsistent wchar_t size
micro_ecc_lib_uECC...
Hi,
I have been trying to use the FATFS example (SDK 15.2) to work with an SD card on the NRF52840 DK, with an Adafruit SD card breakout (I removed the 5V level shifter...
I'm working on a medical device that is using the NRF52832 chipset for communication. One of the tests that I'm required to perform on startup is a RAM check.
On the other...
where is the declaration of board number in ses project? I want to change from pca10056 to pca10059 a project but I did not find where i have to change it in the script. ...
Hi all,
Does anyone know what are the TRC-43 classification of emission section 4th and 5th symbols (see below list for options) for device which is based on nRF52832 and...
Is it possible to connect four peripherals to one central and send 300 bytes of data to the central from each peripheral every 100 msec? If so, which sample program should...
Hi!
We would like to have a peripheral product with an nRF52832 use a public GAP address. Is it okay to just replace bytes 6..4 of the predefined random static address with...
Hi, I am looking for a recent example for twi sensor driven by interrupt(NRF52840), and specifically looking for an example that works with soft device(15.2) and allows for...
Hi folks,
I want to some changes uart project. So i added nrf_drv_timer.c but i din't header file and i encountered 3 errors when i compile my project. Here is some screen...
Hi,
I been looking around at the different questions about SD card interfacing, but can't find the solution I am looking for.
I would like to use the nRF52840 to interface...
