Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I am trying to use the example given on your site
https://github.com/monpetit/nrf52-spi-i2c-master-ssd1306/blob/master/README.md
I am using
IDE-Version: µVision...
Hi,
I would know how many packets per connInterval the nRF52832 and BLE stack are able to manage ?
I see that Android can manage a maximum of 4 packets.per connection...
Hello,
I want to install my own Button & LED handling (not using the default board support). It works on the nRF52840 Dongle, but I also want it to work on the PCA10056...
Hi,
We were testing our product with nrf-Toolbbox.
It seems that in Android 8+ the device gets disconnected and the log screen gets cleared up once the app is put in the...
Hi Experts,
I am trying to design my custom board using nRF52832. I am using Segger jLink Mini EDU to connect/debug the chip/board. I took Thingy:52 as reference and designed...
Hi,
I know there are OTA bootloaders for nrf52 which can be enabled by pressing a button(gpio start) or by sending a message on a bluetooth cahracteristic(buttoless dfu...
Hi,
I am trying to use the SPI with a sensor on our PCB.
Based on the SPIM example, I changed the used pins to match our configuration, where the clock (spi_config.sck_pin...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about whitelist scan filtering.
After pairing and bonding, central would perform...
Dear Team,
i am using nRF51822 Cortex M0 controller , SDK version is 12.3.0(Soft device S130) i want add the PWM Driver, how can i add the driver to existing nRF51822...
hi, I'm using SDK 15.1.0 and s132 I have two custom boards one peripheral and one central. i don't want to use peer manager (according to requirements) And i want the peripheral...
I have modified the ble_app_hids_keyboard_pca10040_s132 example to enumerate as a Gamepad and Modified the GPIO so the buttons send a USB report.
I am now trying to integrate...
Hi,
I am doing some customization for the secure DFU example (SDK15) and i want to add conditions for the update process (battery level for example).
I wonder if there...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
