Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
In order to prevent communication from middle-man attack, I append the signature after ECDH publickey. However, though I get the correct share secret by ECDH, I fail in verifying...
Hi,
I'm using the bluetooth 5.0 and base on the mutilink_center example to add a peripheral and a center. Because I want the center to connect two type device. It could...
Hello,
I have two identical devices with Laird's BL600 chip (that uses NRF51822). They are initialized as NRF_GZLL_MODE_DEVICE and use GZP library (without encryption ...
Hi,
I am trying to write my own bootloader. I gather new image via serial and store it in flash in my application at 0x30000 then invoke reset and in bootloader I want...
Hi,
I was testing the pwr_mgmt project in the nRF5_SDK_13.0.0 with my 52DK, the system off mode seems work fine ,cause the log information is right,but the question is...
Hi,
We are working with NRF 51822 in a multi-role arrangement (SDK 12.3.0, s130_nrf51_2.0.1_softdevice) where one NRF51 will be connected to a phone in peripheral mode and...
when i use pc tools or APP except "nRF Connect" to connect my 51822,i can not find some parameter,so i want to know in example "ble_app_uart",how to set up connect parameter...
So apparently, for ble, all CCCDs, regardless of what the UUID of a characteristic is, is
00002902-0000-1000-8000-00805f9b34fb
And to access that, the proper step...
as im working on nrf51822 sdk 9.im finding difficulty in performing bonding..so could you please help us in providing the code which performs ONLY bonding and advertising...
Hi, nordic staff:
I'm developing a project on nrfready_desktop_2_v3.1.0, as the chip is nRF51822;
I need 3 PWM channels for RGB leds. and i found there is a file named...
Hello all,
We are authorized distributor for Nordic in India (SM electronics) I was looking at
nRF51822 Bluetooth Smart Beacon Kit but in download section i was unable...
Hello,
I'm currently developing an application on nrf52832 that'll use SAADC low power to fetch battery voltage level and report that value on BLE advertising data. I've...
I am trying to use NRF51822 GPIO to generate a pulse with max width of 0.3us. According to other tickets in the forum and the product spec, NRF51822 should be able to generate...
