I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
Dear all,
I have tried using a setting a break point in main() of my program. Without running the softdevice, it is fine to pause in the break point and continue to run...
Hi,
I am developing a product using nrf51822. While pcb designing I am getting a clearance error. Please let me know how to resolve it. All the dimensions are 8mil in clearance...
Hi,
I am editing my question:
I have seen some strange behaviuor I could not explain. In order to test it I have made the next test program:
I am using the application...
Hi,
I recently bought the nrf 51 development kit. Before implementing a BLE application on the board I wanted to start with a simple application of blinking a LED by pressing...
1.I have a nRF51_DK and nrf51822(waveshare core51822)
2.Keil 5.18v and all of the needed software were Installed
3.s130 1.0.0 or 2.0.0 and sdk9.0 or 10.0 were used ...
Hi Nordic Dev Zone, Ray Kampmeier here.
I'm building Direct Test Mode (DTM) into a production application that uses the 110 soft device. Unlike the provided Nordic examples...
Is there any way to integrate SoftDevice with entire project so I can get one hex from build? I am new to CrossWorks and nRF52 and I am developing BLE device. After getting...
I want to do firmware update over the air in a STM32F4xx microcontroller which is connected with nRF51822 chip via UART (TX, RX, CTS, DTR) and BOOT pins. ST microcontroller...
Hi
I can get the current time from the server using the time service characteristic. Which function should I use to set the RTC clock on the nrf 51 to the current time...
When I add a new server of my own service I got a problem.
when I set
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&cccd_md.write_perm);
I can send data to iOS normal,but...
