Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello
I want to setting up DFU in my project. I followed this document :
link text
I'm using IAR EWARM and nRF51_SDK_8.0.0 and "nRF51_SDK_8.0.0\examples\dfu\bootloader...
Dear all,
I have written some code that controls the SPIS and allows it to transfer data as if it were a master. I am generating the SPIS clock from one timer, and I am...
Hi everyone
for my application I must use the Bluegiga dongle like central (PC side) and nRF51822 for peripheral (hardware side).
So I implemented cable replacement app...
I feel stupid asking this question, it should be documented in the standard and the code but I have looked and googled with no luck.
I want to populate the ble_rscs_meas_t...
What are the considerations when choosing between using an external 32.768 kHz oscillator and just using the internal RC oscillator as the low frequency clock source?
Here...
Hi,
Does anyone know if there is windows (8.0) visual c++ command in the BluetoothGatt functions to use the memory request event with S110?
Many Thanks
Hello,
I would like to develop a quick prototype with nRF51/52 however do not have experience in designing apps. I have seen the example apps and was wondering whether...
Hi,
your Central is able to hold 8 connections with peripherals. Perhaps someone is able to explain how more than one connection is handled? If only one Central is connected...
My Project:
I want to control 2 outputs on the nRF51DK from my mobile device(Android & iOS). Its a simple program:
left button is pressed -> PIN 21 High / left button...
Hi ,
I am planning to buy nRF51 USB Dongle(S120 SoftDevice or S130 SoftDevice) to discover BLE devices and to communicate bi-directional. I am planning to develop C# in...
I am using
nrfgo studio ver 1.20.0.2
s132_nrf52_1.0.0-3.alpha_softdevice.hex
nrf52832_xx_aa_s132.hex supplied by Nordic (ble_app_template)
emIDE 2.20
The firmware runs...
Hi,
with the pstorage library, is it possible to store data at a specific flash address?
The background of the question is that I would like to store data in flash, and...
Hi,
I am using PWM for a buzzer. It is working, but the current consumption is always 300uA when PWM is not in use. This minimal current consumption appears right after...
1: my nrf51 SDK board not work , I replace the USB control IC--ATSAM3U1C-AU(the old is ATSAM3U2CA-AU),can you send me the firmwair of JLINK with this IC and the contacted...
Hi Nordic,
I want to know, how the button_push_sequence works on case of handling different events at different button_push sequence like... (--nrf51-ble-app-lbs--)
...
