Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm working with an nrf51822 with the s110 softdevice. So I'm trying to read an analog signal from multiple pins. My program will run fine for quite some time. Eventually...
Hey guys,
I need to record many time interval ?, can i generate system time and use it to record all of my time intervals?
If I want to send all of the time intervals...
The gcc compiler is gcc-arm-none-eabi-4_9-2015q2.
The make version is GNU Make 4.0 (Build for arm-unknown-linux-gnueabihf).
The error message is:
... arm-none-eabi...
So I'm using the spi_master.c from SDK 6.1 to communicate with an LCD driver. I'm using an nrf51822 with s110 softdevice. My system has been sporadically hardfaulting on me...
Hello all,
I have found closed topics here with similar names ( devzone.nordicsemi.com/.../ etc.) but my question is about adding the characteristic with encryption.
My...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including ble_advdata.h compiling with gcc:
In file included from...
Hello,
I know I'm not supposed to use TIMER1 with IRQ 0 when using a SoftDevice but I want to try anyway :) I want to do some bit banging with timing that is timing sensitive...
I am trying to program custom boards with the NRF51822 using an ARM-Flasher with no success. Using J-Flash I can connect to the device properly, program and verify the hex...
What could be the reason for?
Couldn't find any error descriptions.
Using Laird BL620US with newest FW v12.4.14
Error occurs as a response to 'scan start 1000 0 0'...
According to the *.map file the .bss (RAM) usage for my Application is 0x16b8 or 5816 bytes. This is obviously a very high RAM Application, likely due to the abundance of...
Hello Nordic,
I am working on [nrf51822 custom board+SDK8.0.0+SD110]. I need to test button press bouncing and de-bouncing, how it works on the board ? I found one example...
Hi,
is it possible to use this module from LAIRD in connection to the nordic SDK - i installed the softdevice hex but the hrs example for s110 is not running properly ...
Hi.
My nRF51822-mKIT, when attached to the USB port, don't flashes the green LED nor the drive appear on Windows explorer.
It's possible that mbed loader was corrupted...
I have found that when I try and initial the Softdevice to use the Scheduler, shortly after initialization and right before dm_init() runs, I get an NRF_ERROR_NO_MEM error...
Hello,
I am trying to use nRFUart project given with the Master Emulator API, however; the original code crashes while trying to initially reset the hardware device. I...
