I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
When the firmware is run in debug mode (J-Link connected), the system always works correctly. BLE initializes properly, and all sensors function as expected.
When...
Hello, everyone. I am an undergraduate student majoring in Mechanical Engineering in South Korea.
I am currently working on a research project to develop a PPG sensor using...
Hi,
(I'm assuming that the main() function of an application is actually executed as a thread.) I can't find any clear documentation that describes how a thread can suspend...
Hello team,
I am trying to interface the AT45DB641E flash with the nrf54l15 on a custom board. I am using the SPI00 instance.
Below is the configuration I set in .overlay...
Hi Nordic team,
We are working on a design that includes more than 50 peripheral node devices, each capturing sensor data and sending it to a single central receiver. I...
Hi,
I'd like to know how to tune the internal capacitance from the 32MHz crystal.
Specifically, I refered to section 4.12.1.1 Using internal capacitors in the nRF5340...
I am using the nrf52840 in QFAA package, and the external DMIC example receives audio data through the PDM interface. I noticed that the official documentation mentions support...
Hello,
We have been testing/validating sQSPI on nRF54L15.
We tested the sQSPI on two versions of our nRF54L15DK (0.9.2 and 0.9.3).
We are using this sample app: https...
Hello. I have one question.
When configuring RAM with the nRF5 SDK + SoftDevice, if I get the following error: APP_RAM_START=0x20006000 --------------------------------...
Hi,
I'm trying to program the nRF52840 Dongle (PCA10059, 2.1.1, 2023.26). I modified the Bluetooth: Central UART sample to use USB instead of UART and built it for the dongle...
I need to use one IO port of the nrf52832. This IO can not only detect the ECG signal but also achieve system off wake-up. The ECG signal is a PWM signal with a duty cycle...
I managed to somehow semi-brick an nrf52840. I've all but got the system/project working and wrote some instructions on how to install VSC with the appropriate toolchain and...
We are using the NRFJPROG ver 10.24.2 (JLINK Commander ver 8.92) to connect with our NRF52840 target. It fails to connect, here is the log entries:
[2025-Dec-10 17:05:02...
Chip : nRF52833 QIAA
Environment : Visual Code + nRF Connect for VC Code V 2025.8.654 NCS V3.1.0
I am hoping somebody could assist us with a problem we are having achieving...
I'm new-ish to nRF Connect (2025.9). Getting going on a nRF5340-DK. It seems that I can manage flash layout either through the device tree or Partition Manager. We want to...
