Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Like several other folks, I have been attempting to replicate the results in the Matter webinar here , but updating to the v2.1.0 SDK and using the Nordic dev kits I have...
Hi ,
I am working on NRF52840 microcontroller, I want to implement blinky LED for P1.09 GPIO pin, can you please tell me, how to implement that.
Thanks
Hello!
The company that I work for has built a gateway that uses the nrf52832 as a ble central device (nrf5 SDK and the s132 softdevice). Customers frequently ask us to...
Hello Nordic support:
How to reduce nRF9160's LTE-M TX power in coduction test. Is there any AT command to reduce TX power? Or could you give us some guide about how to...
I am diagnosing pin malfunction in a custom board where I have working code from another version of the board which no longer works.
I am developing against NCS w/ VSCode...
Hi,
When asking to change the toolchain version in the VSC extension I get an error message:
Command 'nRF Connect Select nRF Connect SDK Toolchain' resulted in an error...
I am using the current nrf-sdk v2.1.0, which includes a Zephyr version (3.1.99 etc.) which has at the used stage an error with twister: instead of using get_testsuite the...
Hello,
I tried to run the sample Bluetooth: Periodic Advertising but I found some issue.
I'm using SDK v1.9.1.
The first issue was related to advertising creation with...
Before I go deep into the rabbit hole, I am wondering if anyone has had success with the following:
I am in a Windows 11 environment
I want to setup Docker with nRF...
Hi Community & Nordic Semi
I have an ultra low power design using the NRF9160.
I would like to avoid adding an additional LDO to reduce costs and Iq.
VIO from the datasheet...
Hello Community, i'm currently working on a custom board based on BC40C which is a BT/BLe module based on nrf5340 i'm trying to debug my board with jLink ultra + under, i...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
nRF Connect SDK v2.0.0
VS Code 1.70.2
nRF9160 development kit
To view all possible log messages the fololwing logging configuration is set up in prj.conf:
CONFIG_LOG...
