hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hi,
I am working with nrf52840 development kit and raspberry pi 3b module.
Using raspberry pi module i am able to scan and connect to nrf52840 development kit.
Now...
Hallo,
I am currently trying to debug the Matter samples on the NRF5340 DK. They all work fine, but I have a problem with the "Thread Viewer" in VS Code while debugging...
I have cypress ble module that generates carrier with PRBS9 modulation and GFSK on 2408MHz. As a receiver I use nrf52 Dongle and nrf52 DK board. In RSSI viewer I can see signal...
Hello Before we just have to overwrite shouldAutoConnect to enable an automatic reconnection Is autoconnect supported on Android NRF toolbox 3.1.3 (kotlin implementation)...
Hello,
In order to reduce the consumption, I remove some sensors (physically from the board).
Should I change the SW ? Is there any discovery state required that should...
Hi Nordic,
1. I am using bl653_dvk board and (C:\ncs\v2.1.0-rc2\zephyr\samples\drivers\uart\echo_bot) is using for my sample
2. Here is i need to communicate with both...
Good day
sorry if it's not clear, it's a rare problem and I have difficulties to explain it but here goes:
I Have two boards - PCA10056 from nordic and nrf52840 Feather...
Hello,
We have a custom NRF52840 board that can be powered via both Battery and USB. The peripherals that are connected to the board require it to be in high power mode...
Hi,
Build an application without SD but with MBR. MBR is at address 0x0000 - 0x1000. Application is at 0x1000 - 0xF0000. At the beginning of the application is the ISR...
Hi
What is your maximum throughput experienced with Android devices over Bluetooth 5.0+?
On my side, I can reach 340 kbps from Android to a nrf52 based device while transferring...
Hello all,
Two same same nRF52820 modules are connected to two usb ports and they are easily flashed via Segger, namely selected via two JLink emulator numbers.
Two separate...
Dear sir/madam,
My question is: - can you recommend courses/books which can help us to more deeply understand the zephyr RTOS in conjunction with the nordic microcontroller...
Hi,
We are currently developing the nRF52833 (peripheral) with ncs v2.0.0. We would like to calculate the link budget of our system when different smartphones are used as...
Hello
I am working with nrf9160dk_nrf52840 and using the BLE of nrf52
I am using the peripheral uart sample code to send some custom data.
I am trying to send more than...
