Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I'm working on project where I want to scan nearby beacons while participating in a Mesh network. I've configured everything as shown in the sample ble peripheral lbs...
Hi,
I am working with an nRF52832 in the nRF52-DK. I am trying to use the ADC with timers through PPI. I have a timer with five CC events, and one of them through ADC measurements...
I am attempting to establish a PPP connection between an nRF9160 and a Linux device over a UART (hardware flow control is optional). The goal is to allow these devices to...
Hi,
When applying for the SUPL client library i get the error message: "your application for SUPL-C license hase been denied"
I have an active DevZone account
I applied...
I have my code working correctly and for site testing of the first 20 units the customer wants to know the
MAC address so that any glitches can be identified to a particular...
Hi,
we would like to use nRF Desktop to test throughput and show we can send 20B per ms (from peripheral to central).
The LLPM sample is not well optimized, while nRF...
Hello,
Using the nRF Connect SDK 1.9.1 for nRF9160 location. Found the "location" library quite simple and scalable to use. So was looking into it. We do not plan to use...
I bought a PPK (not the PPK2) a while ago, and it's been working fine. However, recently it stopped working. I'm using a JLink EDU mini, and the power profiler app in nrfconnect...
Hi, I'm developing an application using Libuartes to handle GPS data 1. According my knowledge about Libuartes, It will call the NRF_LIBUARTE_ASYNC_EVT_RX_DATA when the buffer...
Hi,
Since BLE advertising consumes current, I want to stop sampling ADC data during BLE is advertising. Are there any BLE events to know when advertising happens or are...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
