HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hey
When i disconnect my nRF5340-DK devkit to my Lenovo T14s Gen 2 running Ubuntu 20.04.3 LTS the usb driver in the linux kernel crashes.
I think it's a problem that...
Hello there,
I've set up a Thread network with a few devices, and now I would like to connect to a ipv4 server.
At home or at the office we do not have a ipv6 public address...
Hi,
We are Migrating from nRF52832 to nRF5340 dual-core soc. In nRF52832 9 off available GPIOs were only to use with a low drive, low-frequency application since they may...
I have starting working with UART. I see that there are two options for configuring it: UART_0_ASYNC and UART_0_INTERRUPT_DRIVEN. I want to use ASYNC option for my UART, but...
Hello
NCS1.8.0 Windows10 X64;
Can [v1.8.0\zephyr\tests\drivers\adc] convert microphone analog signal into digital signal? for I2S 8bit 8kHz
thanks
Best Regard...
Hi, I need to fetch the Device ID of nRF5340 Chip. In datasheet Info.DeviceID[n], n = 0...1 , is mentioned. How to access this information ? Also, I am using nTF5340-DK kit...
Hello
I am planning to purchase Nordic Semiconductor Power Profiler Kit. Before purchasing the kit I need to know, Is this kit supports another company's microcontrollers...
I am using nrf52832 with a custom board with no external crystal oscillator. As bootloader I use "secure_bootloader_uart_mbr" so I don't have softdevice. SDK is 17.1.0_ddde560...
using ble_app_interactive on one dev kit and connecting to pc viewing on terminal
other is my perihperal.
on entering connect <device address> it gets disconnected
hi I sucessfully tested the blinky project on the nRF52840 dongle... btw i'm using vanilla zephyr...
but i'm unable to prototype the uart comm on this board... the board...
I'm working on NCS 1.8.0.
I can use DFU APIs to upgrade my firmware successfully, however, after DFU is finished and system reboot, the McuBoot to swap images is too slow...
Hi, I want to know brief aboout difference and objective of different types of Zephyr projects. When using nRF Connect SDK, in SES a project is created, 3 options are available...
Hello,
I am using the nRF52840 DK board and writing code in Zephyr and I want to change the clock frequency. Currently, I guess by default it is 32.768KHz How can I change...
Hi,
I am using an nRF9160/nRFConnect SDK 1.8.0/VSCode and my application uses MCUBoot and SPM. It is a "non secure" application.
I am trying to get a reset cause.
hwinfo_get_reset_cause...
