I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
Hi Team,
I am developing an application that nordic chips receive data from msp430 chips by the SPI, and send them out.
Nordic can receive the data from the msp430, but...
Hello everyone,
I tried to add the long press event into my bsp_event_handler without success. I get the normal button press event, but the long button press event is not...
Dear Nordic FAE:
Where can I find the nrf52840-CIAA REACH report?
i can not find it by
focenter.nordicsemi.com/index.jsp?topic=%252Fcom.nordic.infocenter.sdk5.v12.2...
