Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
I have developed an application on an nrf51dk, with SDK12.3 (as it was the latest that I could make it work with). It is running fine on the DK, but when moving to the...
Hello.
I am running ble_app_uart altered to allow for connection of two central devices.
The connection of two devices work fine.
Upon each connected central, I can...
Hello! I would like to use a predefined example from the nRF SDK and instead of the board's button, to use an external stimulus (let's say, an external button ). Similarly...
Hey,
I am working on the nRF51 DK and nRF51822 with SDK12,S130, trying to pass a SIG PTS test for required IOPT, however always getting the same "INCONC" verdict, the PTS...
Hi,
I am trying to interface IS25LP064A External Flash with nRF52832 using SPI. I want to get the device ID/ Manufacturer ID of the flash. I am able to get the same in Arduino...
Hi everyone,
I'm using the nRF5SDK160098a08e2 and i tried to compile the ble_app_eddystone exampe but i'm getting this compilation error!
cannot find ../../../../.....
I am unable to read any uart input when I configure UART1 with nRF9160DK.
Please let me know if anything is wrong in my code/config
main.c
nrf9160dk_nrf9160ns.overlay...
In the Sleep mode and nrf52810 was Broadcasting with space 125ms once.
The normal temperature was good,that only 0.08mA. but why not 85℃,The current was up to 0.21 mA ,it...
Hello
I would like to detect timeout when I send a confirmable coap message not received.
My problem is that the response I receive in my response_handler is always...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...