Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I'm using nRF Connect to connect to the secure bootloader. In the debug log I see that an MTU of 185 is requested and 183 is replied. I also see this in the Wireshark...
When I used nrf52840 to connect the peripherals with pc-ble-driver-py, I had my own custom UUID, so I needed to add a custom UUID. I referred to this article , but the following...
Hi,
I know that there are different ways to set up the radio, but generally speaking, is there a general practice for how commercial devices' PHYs are set up when advertising...
Hello people, Honestly this is a problem more related to a Raspberry Pi than the nRF52832 but I'm getting same difficulties here so I will explain my situation. I have been...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
Our hardware has Winbond NAND Flash chip connected to the nordic MCU(nrf52840 /nrf5340). However QSPI cannot be used as nordicSDK doesn't support NAND Flash.
I understand...
Hello,
I am using the Power Profiler Kit connected on top of an NRF52840-DK
I am using IAR and using IAR's J-LINK plugin to program/debug an application on the DK. However...
I am trying the example project ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\l ight_switch' and ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\ dimming' available in nrf5_SDK_for_Mesh_v4...
Hello,
I'm experiencing NRF_ERROR_INTERNAL from a call to pm_peer_new(). While further investigating into this, it turned out, that the p_bonding_data parameter was checkt...
