Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi everyone,
sadly my nRF51-DK boards seems to be terribly bricked.
During firmware update nRFgo Studio (on Windows) stopped responding.
I can't enter bootloader mode...
Hello,
I am currently trying to add SDK15 functionality to a mesh project as shown in the documentation.
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic...
Hello,
I am working on a project with nRF51822, I want to connect two or more nRF51DK boards using SPI and send an interrupt from one board to another, Is there any code...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I would like to ask some questions about Peer Manager.
1. I want to erase all bond when I press a button. Do I just...
Hi,
I have been trying to read the register values, from BNO_080, using the functions nrf_drv_twi_tx to write and nrf_drv_twi_rx to read. But for some reason, i have been...
Hi!
I gave up trying to come up with a working solution for updating mesh nodes based on SDK1.0 to SDK2, see https://devzone.nordicsemi.com/f/nordic-q-a/37707/dfu-update...
Hi,
I read this post to handle communication with both built in UARTs
I'm working with Mesh SDK 2.0.1 and nRF SDK 15.0.0 at the moment.
My application uses UART0 initialized...
I noticed that the secure bootloader by default protects bond information during FOTA. In earlier SDK versions there was something called preserved pages right below the bootloader...
Hi, Im using this library, https://github.com/NordicSemiconductor/Android-BLE-Library/, Everything works great except the disconnect part, I need to press the disconnect button...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
• nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip • nRF...
Hi,
I have been working through the examples for DFU with the nrf52832 dev kits from the SDK (nRF5_SDK_15.0.0_a53641a) from this folder:
...\nRF5_SDK_15.0.0_a53641a\examples...
Hi, Guys, I have problem with my nRF51822. I built the ble_app_uart project in the SDK v6 and and flashed it on the mcu using j-link and I also flashed S110 SoftDevice version...
