Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm having trouble writing to a gatt characteristic using the python bindings for pc-ble-driver
Service discovery works fine, I managed to connect to a BLE server and reading...
I have a device that I need to control, that needs 2 different square wave signals of different frequencies (although they may be multiples of each other), one at around 4...
Hi all. I try to run capacitive sensor example on nRF52832 with my hand made capacitive sensor which I made according to this tutorial devzone.nordicsemi.com/.../.I connected...
Hello,
When i execute a function that uses TWI from a timer handler the NRF gets stuck.
I assumed that this issue occurs because of interrupt priority so i gave the TWI...
after connecting and disconnecting advertisment not stopping when i try to stop it ( sdk 11). Without establishing connection i am able to stop it. Nrf51822
Hello
I am trying to create secure connection between peripheral device and mobile app & central device.
I created my own custom service and want to make them secure...
Hello,
My goal at the moment is to be able to configure my peer device which utilize ble_app_uart example so it would connect only to a specific master device e.g. android...
I am using BLEPeripheral and MySensors libraries and nRF51822 device(client side).
I want to change functionality, if I press key of nRF51822 device it should start to advertise...
I have a PCA10040 working with the mesh sdk.v1.0.0 serial example. I can do an Echo via the Python interactive_syaci and get a back a response. I have seen the documentation...
Hi Nordic
I am running ble and ANT + bsc code on our custom board. However, since the sd_softdevice_enable function does not return, I asked the question once. devzone.nordicsemi...
hi i am using nrf52832 soc with sdk14.2.0 ble_central_multi-link example with soft-device s132v5.0
i want to know that is that any way to set connection handle number can...
hi,
i am using nrf52832 mcu with sdk 14.2.0 and with softdevice s132v5.0.0 with ble_app_multilink_central example to connect with nordic thingy 52 as ble peripheral to...
Hi,
I noticed you have added C13 and C14 (12pF) caps. However, they are not visible on Infocenter's reference circuitry. What are these caps for and why they should be...
PDM Initialization normal,I enable PDM and start PDM sampl,I find not jump to NRF_PDM_EVENT_END irq,This is when the link is broken.I suspect not get data in RAM,can you gave...
