Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
hi
I mistakenly left the inductor connected between the dcc pin and the DEC 4 pin and let it operate in the LDO mode.
What kind of problem will you encounter?
Or maybe...
hi all, I want to learn about HCI layer . It has 4 packet and I dont understand about HCI ACL data packet and HCI synchronous data packet . how are they diffent? Packet from...
-Dear Nordic Devteam
Thanks for your endeavor for the nRF Sniffer 2 . Although it is a beta version, this is sincerely anticipating.
To set up the Sniffer you will...
I am developing some firmware using SDK 8.1 where power consumption is absolutely critical. The firmware will make a ble connection between the central and peripheral device...
I'm facing a strange problem that I don't really understand:
I'm using 51822 (s130) on a custom board to communicate with iPhone 5S. The parameter that is able to establish...
In multi-link central app, after BLE_GAP_EVT_CONNECTED event, BLE_LBS_C_EVT_DISCOVERY_COMPLETE is called NRF_SDH_BLE_CENTRAL_LINK_COUNT number of times.
So For example...
Hi,
I use the original "nRF5_SDK_14.2\examples\ble_peripheral\ble_app_uart" no any modification, in Keil the .hex file size is 71k while it is 153k in SES.
My questions...
I am working on SDK V10.0.0 because I need S310 softdevice.
I like SEGGER_RTT I used in SDK V11 and V12.
But I got the Error in the subject line.
I had to uncheck use_microlib...
Hi,
I build below sample in SES and receive an error for:
Compiling ‘nrf_log_backend_serial.c’
can't open '...nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
